Large car weighbridges are prepared from pre-installation to post-installation using the entire process in detail
  Electronically, especially large-scale automobile platform scales, widely used in mining, grain processing, coal gangue crushing industry, brick factory, quarry, port, chemical plant, warehouse and other institutions, its superior performance and stability, not only improve the industrial and mining The efficiency of the company's inbound and outbound material settlement is deeply applied to the monitoring of the production process and the comprehensive data management of the enterprise to meet the modern weighing requirements.
Get to know the next big car weighbridge from the pre-installation work to the post-installation process using the entire process:
1. Truck scale / weighbridge pit form:
     There are two types of foundation pits for the weighbridge . One is a foundation pit and the other is a shallow foundation pit. The shallow foundation pit refers to the installation method in which the floor scale is installed in the foundation pit, and the surface of the weighing platform is level with the ground. The floor scale without the foundation pit is installed above the ground , and can be cleaned frequently , without water accumulation , and the cost is relatively cheap.
2. Truck scale / floor scale site selection: Â Â
    The installation site of the weighbridge should have a good drainage channel , and will not flood the weighbridge due to heavy rain or flash flood . For shallow foundation pits , drainage channels should be provided. In addition , both ends of the weighbridge must have a straight road of sufficient length for the car to be lifted up and down , and the straight ends at both ends should be at least equal to the length of the weighing platform.
       Another factor that affects where the scale is installed is the number of cars you want to weigh each day. If you only weigh about 20 cars a day , one platform should be enough , and you should set up a two-phase road . If you have to weigh about 50 cars a day , you need to prepare for parking . A platform should also be enough. , zui good and then prepare a bypass; if well over 100 cars a day, you should consider two platform scales simultaneously, each weighing in both directions can weigh heavy vehicles or empty, and use a bypass.
       You should consider: Where should the car stop? Do you have to queue when you are overweight? What happens when there is heavy snow, heavy rain or during the peak season? Waiting for the problem , you need to pay attention.
3. Â Truck scale / weighbridge foundation construction:
    Pouring concrete foundation platform must, this base must be excavated to the following local permafrost line in the construction should ensure that the concrete numerals, pouring embedded parts to ensure that the level, position, etc. of the geometry, but also to ensure that when the pre-concreting The embedded parts are not displaced. After the foundation pouring is completed , it should be maintained according to the civil construction code , and the concrete can reach the design strength index before installing the weighbridge. If you want to shorten the curing cycle, allow to take measures to add "early strength", and other professional and technical personnel under the guidance of the construction. To mine, you should set a ground rod according to the local conditions and to ensure that the grounding resistance <4 ohms, the center position of the weighing platform from the room to be laid one pound iron pipe, through a signal cable.
       Please refer to my basic view of the company's foundation construction, general construction period plus basic maintenance period, before and after probably need about 5-10 days.
4. Truck scale / weighbridge :
     Should be close to room lbs weighbridge for weighing instruments placed, or computers, printers and other devices, in addition, to ensure pound member may also be a driver, a single transmission Division scales, the scales ensure automobile, license plate number to check the identification of goods and the like .
5. Truck scale / weighbridge installation and verification:
   In most cases , the unit of measurement is responsible for installation and commissioning , and the manufacturer assists in the installation . The following items need to be prepared:
      2 cranes ( or forklifts ) and jacks ( greater than or equal to 5t) .
      Level, welding machine and handyman.
      After the installation and commissioning of the weighbridge, the certificate is qualified and issued a certificate of conformity before it can be officially activated.
6. Truck scale / weighbridge technical parameters: Â
* Electronic truck scale weighbridge weighing range : 30t~200t
* Truck scale equipment power supply: 220V~ 50Hz
* Metric accuracy : National OIML Level III Accuracy
* Electronic truck scale sensor operating temperature: -30 °C  ~ +70 °C
* Weighing platform specifications: GB 4235 module structure series carbon steel weighing platform, multi-unit combination Â
* Output method: junction box connected with high precision sensor  , XK3190 series display instrument display Â
* Optional accessories: optional printer, data networking, disk storage, and with weighing software for data management
The technical parameters of a platform weighbridge , this relates to the scope of your future use. If you have some special functional requirements for the weighbridge, you must communicate with the weighbridge manufacturer , let the manufacturer produce it in one go, if it is not ready for production. Rework, it will take time and effort!
Kn95 Cup 3D Mask,Kn95 Protective Mask,Kn95 Face Mask Online,Non-Medical Kn95 Face Mask
Jiangmen anjian biotechnology co. LTD , https://www.jmanjianmask.com